카지노 엘에이s in Display Fabrication: Cell and Polarizer Cutting
Only CO2카지노 엘에이s can cut display “cells” and polarizers with the speed and edge quality needed for cost-effective, high-volume production.
October 4, 2022 byCoherent
The world’s biggest카지노 엘에이 manufacturersmake over one million 카지노 엘에이s every single day. Doing this requires extremely high-speed production processes.
This rapid throughput is easier to achieve in the initial production steps. That’s because the first part of the FPD production cycle is performed on mother glass panels containing well over a hundred 카지노 엘에이s. This allows steps likeELAandLLOto process all the 카지노 엘에이s on the mother glass simultaneously in a single operation.
But things change when that large panel is separated into “cells.” This means 카지노 엘에이 it up into individual displays, or sometimes groups of just a few. By its very nature, this cell 카지노 엘에이 operation can’t be done simultaneously over the entire panel. It’s a serial operation.
Of course, manufacturers don’t want cell 카지노 엘에이 to be a production bottleneck. This process must still keep pace with the rest of the production flow.
Read the other blogs in this series on 카지노 엘에이s in display fabrication |
|||
The kindest 카지노 엘에이
Theoretically, at least, 카지노 엘에이 through the thin, flexible OLED displays could be easily accomplished using a variety of different methods. However, this particular application presents a few unique problems.
First, each display is only separated from its neighbor on the panel by a few millimeters. Second, the display is a stack of heterogeneous materials, each of which may have different 카지노 엘에이 characteristics. And, finally, the displays are relatively delicate electronic devices. They can be damaged by heat or anything else that causes the various layers to physically separate at all.
CO2카지노 엘에이soffer the best way to optimize the cut, within all these constraints. These 카지노 엘에이s produce high-power infrared light which is well absorbed by all the various materials in the OLED stack, meaning that every layer is efficiently cut. Plus, they cut without producing any debris which might affect display appearance or functionality or require extra production steps to remove.
For cell and polarizer 카지노 엘에이, the focused CO2beam is usually delivered using a high-speed, precision scanning system. This provides the required throughput rate and yields straight 카지노 엘에이s with narrow kerf width.
Cell 카지노 엘에이 is a multi-layer problem
But the high 카지노 엘에이 power which enables rapid cutting can also be too much of a good thing. This is because the infrared light from the CO2카지노 엘에이 cuts by a thermal mechanism. That is, it heats the material up until it vaporizes. Putting too much heat into the part during cutting can create a large heat-affected zone which damages the display circuity.
Also, both the bottom and top layers of a flexible OLED display are polymers. When this plastic is heated during 카지노 엘에이, some of the material melts but doesn’t boil away. Then, it tends to flow and resolidify in a “bead.” That is a slightly thicker lip on the edge.
This lip creates an issue in subsequent production steps, in particular when a contrast enhancement polarizer is added on top of the OLED 카지노 엘에이. This polarizer is also CO2카지노 엘에이 cut and could experience the same problem with edge thickening.
Schematic drawing illustrating the problem of display cell 카지노 엘에이 using a CW CO2 카지노 엘에이.
When these two parts are laminated together, the edge lip can create bubbles or gaps between the layers. This is highly undesirable.
Modulated CO2카지노 엘에이s are a cut above
The way to avoid creating a lip at the 카지노 엘에이 edge is to modulate the CO2카지노 엘에이. That means rapidly turning the beam on and off. This still supplies enough heat to vaporize the material. But it doesn’t keep the 카지노 엘에이 on long enough for that heat to propagate very far into the substrate where it will melt material, rather than completely remove it.
There are two different ways to modulate a CO2카지노 엘에이. The first is to take a 카지노 엘에이 that produces continuous output and then chop that up into pulses with an external acousto-optic modulator. That’s what’s done in the CoherentDIAMOND Cx10LDE+, which is currently the most popular 카지노 엘에이 for cell and polarizer cutting in the FPD industry.
One reason the CX10-LDE+ is so widely used is that the modulator is directly built into it. This approach allows us to fully integrate the 카지노 엘에이 and modulator control electronics and therefore optimize total system performance. This is critical to reaching the precision in pulse control and power stability needed to achieve the process consistency and repeatability required by FPD manufacturers.
The second way to modulate a CO2카지노 엘에이 is q-switching. Here a modulator is placed inside the 카지노 엘에이 resonator itself so that the 카지노 엘에이 operates in a pulsed (rather than continuous) mode. This makes a big difference in how the 카지노 엘에이 operates. Thus, while an external modulator provides microsecond range pulse widths, q-switching produces much shorter, nanosecond regime pulse widths and also increases the peak pulse power dramatically.
These shorter pulses reduce the heat-affected zone even more, and also allow greater precision and control over the 카지노 엘에이 process. As a result, many FPD manufacturers are transitioning to this technology. The CoherentDIAMOND Cx-10LQS+is the only q-switched CO2카지노 엘에이 commercially available.
Reliability saves money
Another reason whyCoherent 카지노 엘에이sare so widely used in cell and polarizer cutting is their lifetime and reliability, plus our global service infrastructure. Once again, FPD makers are producing very large volumes of products continuously. Production downtime to service or replace a 카지노 엘에이 has a huge productivity and cost impact. The unmatched lifetime of these 카지노 엘에이s – typically in the 10,000-to-20,000-hour range – ensures an uninterrupted flow of high-quality FPDs. And, when 카지노 엘에이 replacement is finally called for, Coherent’s worldwide inventory andquick-response service teamensure it’s swapped out without delay.
Learn more about our카지노 엘에이 solutions for display manufacturing.
